Home Repair Forum - Powered by vBulletin

Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles Blog Blogs Groups Groups
  • ctbale's Avatar
    Yesterday, 09:28 PM
    ctbale replied to a thread Monitor 422 Burn Pot Drip tube in Monitor Heaters
    Thanks! he says its running great but i have been wondering about that. Got two 422s that NOW run but the burn patterns say need to come apart. ...
    see more
    2 replies | 61 view(s)
  • hawkins111's Avatar
    Yesterday, 12:11 PM
    hawkins111 replied to a thread Monitor 422 Burn Pot Drip tube in Monitor Heaters
    The 422 does have a inner piece for the nozzle port, it doesn't stick out into the center of the burner. That piece has to be installed or the brass...
    see more
    2 replies | 61 view(s)
  • ctbale's Avatar
    Yesterday, 04:11 AM
    ctbale started a thread Monitor 422 Burn Pot Drip tube in Monitor Heaters
    So last year I rebuilt a friends 2 heaters. A 2200 and a 422 The question I have is I noticed that the 422's Burn Pot did not have an extension...
    see more
    2 replies | 61 view(s)
  • ctbale's Avatar
    Yesterday, 02:41 AM
    ctbale replied to a thread E01 in Monitor Heaters
    Wire was good. I pulled the connector off the mother board. At first it cleared the E1 fault, plugged it back in and it ran for a while then came...
    see more
    9 replies | 2223 view(s)
  • rrob311's Avatar
    12-11-2018, 08:10 PM
    rrob311 started a thread M21 heater loud transformer sound when heater fan kicks on in Monitor Heaters
    I went through the burn chamber on my spare m21 heater and test fired it earlier. It worked ok so I shut it down. Went to fire it back up and it went...
    see more
    0 replies | 41 view(s)
  • FordMan59's Avatar
    12-11-2018, 02:10 PM
    FordMan59 replied to a thread E01 in Monitor Heaters
    If it's a main board check eBay often there will people selling used ones at a fraction the cost of a new one. I bought a spare one for my 422's in...
    see more
    9 replies | 2223 view(s)
  • ctbale's Avatar
    12-11-2018, 02:59 AM
    ctbale replied to a thread E01 in Monitor Heaters
    Working on two 422s One of mine has the E1 code also. Book says like above post says flame rod or wire is grounding. Will investigate that...
    see more
    9 replies | 2223 view(s)
  • mrcaptainbob's Avatar
    11-23-2018, 10:47 PM
    mrcaptainbob replied to a thread 1" braided stainless.... in Plumbing
    Don't need it anymore. Will use copper and a couple of 90* Sharkbites.
    see more
    1 replies | 231 view(s)
  • mrcaptainbob's Avatar
    11-21-2018, 06:01 PM
    mrcaptainbob started a thread 1" braided stainless.... in Plumbing
    I'd like to connect the water softener (1" inlet/outlet) to the house water system (1" copper) using 1" braided stainless. Or braided anything....
    see more
    1 replies | 231 view(s)
  • mrcaptainbob's Avatar
    11-20-2018, 01:38 PM
    mrcaptainbob replied to a thread Water softener replacement.... in Plumbing
    It's been awhile. The water from the new well isn't bad at all. BUt I have been getting 'complaints' lately. Ordered a Fleck with metered head....
    see more
    5 replies | 1834 view(s)
  • hawkins111's Avatar
    11-14-2018, 01:24 PM
    hawkins111 replied to a thread Laser 73 heater vibration in Toyo Heaters
    The Toyo blower is a dual function unit. It sucks air in on the bottom fan and blows exhaust out by the top fan. The Toyo combustion system is not...
    see more
    4 replies | 528 view(s)
  • rrob311's Avatar
    11-13-2018, 08:16 PM
    rrob311 replied to a thread Laser 73 heater vibration in Toyo Heaters
    Is there an easy way to clean it? Do I remove the blower? How would it get carbon in it? Isn't it just drawing in outside air?
    see more
    4 replies | 528 view(s)
No More Results