Home Repair Forum



Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 01-07-2004, 07:46 AM
New Member
 
Join Date: Jan 2004
Location: .
Posts: 1
mphall
Repairing PVC Drain Pipe

I have a 3" vertical PVC drain pipe that was pierced by a support bracket for a closet shelf system. The problem wasn't noticed until the upstairs bathroom had been used for a couple of months and mold became visible on the closet drywall.

The hole is 1/4" and do to the pipe's location against a wall stud the builder's plummer is planning on repairing it with what he calls "glue." I am not confident that this is a permanent solution to the problem and I am wondering what I should accept as a minimum standard for this repair. What options exist for this type of repair?

mph
Reply With Quote
  #2 (permalink)  
Old 01-07-2004, 07:59 AM
Journeyman
 
Join Date: Nov 2003
Location: .
Posts: 440
Hube is an unknown quantity at this point
Since this is a DRAIN pipe, and not a SUPPLY pipe, It should be a permanent repair providing the PROPER "weld " glue is used. This won't be the first time a damaged pvc DRAIN pipe was repaired with a solvent glue. No problem. Hube
Reply With Quote
  #3 (permalink)  
Old 01-07-2004, 10:23 AM
Jimmer's Avatar
Apprentice
 
Join Date: Oct 2003
Location: Fredericton, NB, Canada.
Posts: 273
Jimmer is an unknown quantity at this point
Here is the picture of his damage...



Jim

'Just a handyman trying to help'
Reply With Quote
  #4 (permalink)  
Old 01-07-2004, 02:29 PM
Handyman
 
Join Date: Nov 2003
Location: Phoenix.
Posts: 177
irregularjoe
Glue could work, but if it were me I would cut out a six inch section of it and put in a repacement piece using two fernco couplers.
You'd have a bigger drywall hole to patch afterward, but it would be a better fix.

Did you ever see OHM'S mother in LAW?...... SHOCKING!
Reply With Quote
  #5 (permalink)  
Old 01-12-2004, 09:29 AM
JC JC is offline
Handyman
 
Join Date: Dec 2003
Location: .
Posts: 38
JC
That is quite common. "Glue" should be just fine as the line is not under pressure. You can even use a constuction adhesive (I have used polyurethane) and DIY. [8D]
Reply With Quote
  #6 (permalink)  
Old 01-16-2004, 08:36 PM
King
 
Join Date: Jan 2004
Location: .
Posts: 889
mrcaptainbob is an unknown quantity at this point
WOW! That looks EXACTLY!! like the job I did on mine! (Who'd have guessed the upstairs drain would be EXACTLY!! on center with the downstairs toilet?!) I used a circle cutter on the drywall, doped in some 'Plumber's Goop', replaced the circle and patched it up. Been over six months with no problems.
Reply With Quote
  #7 (permalink)  
Old 01-19-2004, 03:25 PM
New Member
 
Join Date: Jan 2004
Location: .
Posts: 6
slowlearner
Oddly enough I did the SAME EXACT THING in my laundry room. It was a wire weld shelf and I put a support screw right into the pipe. Hole leaked about 6 months later. The pipe is 3" and not under any real pressure so I just plugged it with the plastic support and then used PVC cement and cut the nubb flush. Not a leak since. I think the only reason I even saw the water stain was because there were two showers going at the same time upstairs.
Reply With Quote
Reply

Bookmarks



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

» Stats
Members: 10,154
Threads: 6,799
Posts: 28,103
Top Poster: HayZee518 (3,840)
Welcome to our newest member, The zzz Man
» Links

» Online Users: 45
0 members and 45 guests
No Members online
Most users ever online was 388, 07-01-2007 at 02:54 AM.
Powered by vBadvanced CMPS v3.0.1

All times are GMT -5. The time now is 11:29 AM.


A vBSkinworks Design
Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.1.0