Home Repair Forum
Go Back   Home Repair Forum > Indoor Home Repair > Projects
Register Chat FAQ VB Image Host Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 11-13-2004, 09:03 PM
Troy's Avatar
Moderator
 
Join Date: Jul 2002
Location: USA.
Posts: 525
My Photos: (1)
Troy is an unknown quantity at this point
Bathroom Remodel

We hired part of this job, so I don't want to seem like I am taking the credit for these pictures. Here are some before shots:








Try
Reply With Quote
  #2 (permalink)  
Old 11-13-2004, 09:06 PM
Troy's Avatar
Moderator
 
Join Date: Jul 2002
Location: USA.
Posts: 525
My Photos: (1)
Troy is an unknown quantity at this point
We did most of the demo ourselves. Removed a closet and reclaimed a few feet from the hall by moving the door back.:







Try
Reply With Quote
  #3 (permalink)  
Old 11-13-2004, 09:11 PM
Troy's Avatar
Moderator
 
Join Date: Jul 2002
Location: USA.
Posts: 525
My Photos: (1)
Troy is an unknown quantity at this point
The door is moved back and a closet is gone:

Back of the tub is now a half wall, and new tub and limestone is installed:


More to come as we progress. Next is the cabinet and counter top, as well as some painting!

Try
Reply With Quote
  #4 (permalink)  
Old 11-19-2004, 09:12 AM
New Member
 
Join Date: Nov 2004
Location: .
Posts: 2
My Photos: (0)
mnnightowl
Troy, thanks for posting your pics... I'm currently attempting a very similar project (replacing 1963 pink tile/toilet/tub). I have a few questions for you if you have a moment.

(1) I noticed that you laid new floor tile over the old floor tile. My flooring is almost identical to your old tile and it appears to be adhered using cement. Did you contemplate removing the old floor tile or is that something which should not be attempted? I was leaning toward removing my old tile for a couple reasons: (1) I've already got a 1/2" or so rise from the hallway to the bathroom and I'm a little concerned going higher than that; (2) Being unfamiliar with how my toilet is fastened to the floor, I was unsure how/whether raising the floor level will interfere with attaching a new toilet to existing plumbing/bolts. Having taken a couple hammer hits to the cement however, your method of overlay looks like heaven to me.

(2) Did you need to resize your door given the new floor layer? Is it as simple as sawing off 1/2" off the bottom of the door?

(3) I believe/fear my old tub is very heavy and I don't have much awareness of what areas it is connected to the floor/wall. I've never attempted or witnessed tub removal... was yours hard to extract?

(4) My tub is currently surrounded by a 3 wall enclosure. Some of your pics look like you had a similar 3-wall enclosure but some pics look like you took out one of the walls? I don't think I have the ability to move existing walls... was your new whirlpool tub an identical size?

Thanks in advance for any help/guidance you can provide!

Jim
Reply With Quote
  #5 (permalink)  
Old 11-22-2004, 12:23 PM
Troy's Avatar
Moderator
 
Join Date: Jul 2002
Location: USA.
Posts: 525
My Photos: (1)
Troy is an unknown quantity at this point
Quote:
quote:Originally posted by mnnightowl

Troy, thanks for posting your pics... I'm currently attempting a very similar project (replacing 1963 pink tile/toilet/tub). I have a few questions for you if you have a moment.

(1) I noticed that you laid new floor tile over the old floor tile. My flooring is almost identical to your old tile and it appears to be adhered using cement. Did you contemplate removing the old floor tile or is that something which should not be attempted? I was leaning toward removing my old tile for a couple reasons: (1) I've already got a 1/2" or so rise from the hallway to the bathroom and I'm a little concerned going higher than that; (2) Being unfamiliar with how my toilet is fastened to the floor, I was unsure how/whether raising the floor level will interfere with attaching a new toilet to existing plumbing/bolts. Having taken a couple hammer hits to the cement however, your method of overlay looks like heaven to me.

(2) Did you need to resize your door given the new floor layer? Is it as simple as sawing off 1/2" off the bottom of the door?

(3) I believe/fear my old tub is very heavy and I don't have much awareness of what areas it is connected to the floor/wall. I've never attempted or witnessed tub removal... was yours hard to extract?

(4) My tub is currently surrounded by a 3 wall enclosure. Some of your pics look like you had a similar 3-wall enclosure but some pics look like you took out one of the walls? I don't think I have the ability to move existing walls... was your new whirlpool tub an identical size?

Thanks in advance for any help/guidance you can provide!

Jim
In response to your questions:
1) We did remove the old floor tile. It isn't shown from the pictures, but we removed all the tile from the walls and the floor. We brought it down to the sub floor, especially since the plumbing was done from above. we then brought the new tile to approximately the same height, so the toilet will sit in the same place.

2) I did have to cut the door off the bottom about a half an inch. A circular saw made this easy.


3) We paid someone to remove the old tub. It wasn't easy. I believe they broke it into pieces for easy removal.

4) The whirlpool tub was a close fit, but not identical. We removed the back wall of the tub to replace it with a limestone shelf with a glass enclosure. We felt it would make the room seem larger to not have it cut in half by that wall. It also made putting the new tub in a snap. It wasn't hard to remove the wall, there was no electrical or plumbing in it, so a sledgehammer did the trick.


Any other questions? Post some pics of your project!



Try
Reply With Quote
  #6 (permalink)  
Old 11-23-2004, 12:49 PM
New Member
 
Join Date: Nov 2004
Location: .
Posts: 2
My Photos: (0)
mnnightowl
Troy,

Thanks for your responses. I must have only been looking at the pic showing the section under your vanity when I assumed you'd left all old tilework. I ended up removing my old tile, but just down to the mortar base.

Additional question:

Did you run a dedicated electrical outlit under the tub for the motor/heat or did you tap into an existing line serving your bathroom?

I'm definitely taking pictures as I go and I'll post them here when the job is done.
Reply With Quote
  #7 (permalink)  
Old 11-23-2004, 03:33 PM
Troy's Avatar
Moderator
 
Join Date: Jul 2002
Location: USA.
Posts: 525
My Photos: (1)
Troy is an unknown quantity at this point
Quote:
quote:Originally posted by mnnightowl

Troy,

Thanks for your responses. I must have only been looking at the pic showing the section under your vanity when I assumed you'd left all old tilework. I ended up removing my old tile, but just down to the mortar base.

Additional question:

Did you run a dedicated electrical outlit under the tub for the motor/heat or did you tap into an existing line serving your bathroom?

I'm definitely taking pictures as I go and I'll post them here when the job is done.

Yes there is a electrical outlet running underneath the tub with a gfci outlet. It isn't on a dedicated breaker, but it is the only thing that will be plugged into it. We tapped off an existing line.

I should have some more pictures to show soon. Now we learn our counter top will take three weeks to deliver, the glass will take a while too. We tried to keep a schedule, but you know how that goes

Try
Reply With Quote
  #8 (permalink)  
Old 12-14-2004, 08:16 PM
Troy's Avatar
Moderator
 
Join Date: Jul 2002
Location: USA.
Posts: 525
My Photos: (1)
Troy is an unknown quantity at this point
We got our cabinet, counter and sink installed:






Try
Reply With Quote
  #9 (permalink)  
Old 12-14-2004, 08:56 PM
King
 
Join Date: Jan 2004
Location: .
Posts: 871
My Photos: (0)
mrcaptainbob is an unknown quantity at this point
Great job, Troy. But I feel like I'm one of those porn types.....I only look at your project when I'm sure my wife won't walk in on me! You see, I promised her a similar update on her bathroom. That was last year. I'm startin' to hear quite a bit about it the last couple weeks, too!
Reply With Quote
  #10 (permalink)  
Old 12-14-2004, 09:51 PM
Troy's Avatar
Moderator
 
Join Date: Jul 2002
Location: USA.
Posts: 525
My Photos: (1)
Troy is an unknown quantity at this point
That is funny! Didn't mean to get you in trouble. In your defense, my wife planned 95% of this project herself. She picked the materials, designs, etc. All I did was a little grunt work and helped meet the plumbers, etc. []

Try
Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

» Forum Navigation
     > Forum News
     > Illustrations
     > You Gotta Laugh!
     > Catch All
     > Plumbing
     > Electrical
     > Flooring
     > Wall Coverings
     > HVAC
     > Stenciling
     > Appliances
     > Audio & Video
     > Projects
     > Faux Painting
     > Painting
     > Gardening
     > Decks & Fences
     > Outdoor Projects
     > Garage Doors
» Links

» Search

Home Repair Forum
Google   
» Online Users: 18
1 members and 17 guests
Troy
Most users ever online was 388, 07-01-2007 at 01:54 AM.
Powered by vBadvanced CMPS v2.2.0

All times are GMT -5. The time now is 01:59 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.1.0