Search:

Type: Posts; User: hidden 1; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    1,859

    thanks Ive already done that since this is a...

    thanks
    Ive already done that since this is a area i had to regrade and slope the water a certain direction .I had extra cement left over also..That helps with flowing on past the piers ,outside...
  2. Replies
    5
    Views
    1,859

    ive placed in concrete the supports for beam to...

    ive placed in concrete the supports for beam to go on .
    Is it a good idea to pour a little more around the base area and slope the concrete away from pier ?
    the top or the pier is only 3 or 4...
  3. Replies
    5
    Views
    1,859

    piers set up/deck

    I have poured the concrete piers for a fairly low deck -2 ft deep in ground 8 inches round in sono tub with the rebar ,temp has been around 60-75 with low humidity in Tn for 2 days.When can i start...
  4. Replies
    5
    Views
    1,248

    no transformer on it

    no transformer on it
  5. Replies
    5
    Views
    1,248

    The switch,new, popped breaker on its own when...

    The switch,new, popped breaker on its own when turning on..but didnt before.Its a different fixture so i have not used it in on position a lot just a few times here and there.
    I did a test on...
  6. Replies
    5
    Views
    1,248

    switch loop circuit

    Hi i am having a issue with my 15 amp switch loop light circuit and wanted to know whick tests to perform on it.I had the breaker kick a time ot two after using a 3light, light fixture with the...
  7. Thread: wiring

    by hidden 1
    Replies
    8
    Views
    1,909

    done

    I tapped off of a different 20 amp -not kitchen or bath,non dedicated and not many outlets on it.I will transfer a few off it also.
    Whats the max on outlets?
  8. Thread: wiring

    by hidden 1
    Replies
    8
    Views
    1,909

    then why is the outside outlet already in that...

    then why is the outside outlet already in that circuit if its bath only?
  9. Thread: wiring

    by hidden 1
    Replies
    8
    Views
    1,909

    12/2

    I will go a little further then and link into the 20 amp (Gfi in breaker)-already used for bath, and run 12/2 to the outlets. I may leave lighting on the 14/2.
    What is the max outlets i can ...
  10. Thread: wiring

    by hidden 1
    Replies
    8
    Views
    1,909

    wiring

    I already have a 14gauge 15amp light circuit (7 cfl lights) .Am running it 15 ft uf to detatched shed (no other wire nearby).How many plugs can be added to circuit (was going to do 3 and 2 cfl...
  11. Replies
    3
    Views
    1,653

    garage door questions

    How large a door will a 1/3 HP lift,uninsulated?

    When installing horizonal tracks is it better to slope a tad toward the stop screws?

    Any tips on torsion spring installs?
  12. Thread: running wire

    by hidden 1
    Replies
    3
    Views
    1,781

    info

    I will be staying with a 15 amp gfi even though the line is 12 its on..I dont believe you can put a 20 amp plug in item into a regular 15 amp plug.Did you mean combined amp as in if several are...
  13. Thread: running wire

    by hidden 1
    Replies
    3
    Views
    1,781

    running wire

    I am running 12 guage (made for underground) 20 feet to a garage.I will be linking into the 15 amp light circuit.It currently has 6 lights on it -energy efficient lights.How many additional lights...
  14. Replies
    5
    Views
    3,905

    hi ive found that the stuff called goof off in...

    hi
    ive found that the stuff called goof off in the steel /tin container -really cuts through a lot,but unsure if it would damage the siding..it eats away at a lot of tough stuff with a combo mix...
  15. Replies
    3
    Views
    2,094

    Hi i just installed some ,does it ever rust..i...

    Hi i just installed some ,does it ever rust..i know its galvanized but just asking.=Wwill it help to prime/paint it also?
  16. Replies
    19
    Views
    5,103

    thanks but i do my own and have leads if i cant....

    thanks but i do my own and have leads if i cant.
    I will tap into main line after regulator- for the teeed single line thats not regulated- and cap that line( single high line- un regulated) off......
  17. Replies
    19
    Views
    5,103

    aready got one on main line..id rather t off of...

    aready got one on main line..id rather t off of it before water heater...but its not effecting much as long as its off on that line is it.its 80 at meter so im told
  18. Replies
    19
    Views
    5,103

    Hi the teed line (-before main line in -that...

    Hi
    the teed line (-before main line in -that is regulated)-goes straight to washer spicket and reads around 80 psi with some jumps to 110-120 on both needles.

    - it is electric water heater ...
  19. Replies
    19
    Views
    5,103

    figured it out

    hey..i found out the change in spike was a teed in- stand alone - seperate line off the main going to washer before main incoming entered home.
    I set regulator on 55 and expansion tank on 45-is that...
  20. Replies
    19
    Views
    5,103

    thanks but if line pressure is hitting 75...

    thanks but if line pressure is hitting 75 sometimes 80-spike should the tank be at just 40?...i thought it is to be closer in pressure.is set for 62 on regulator but goes up off/on
  21. Replies
    19
    Views
    5,103

    thanks. so it will work in any position then?...

    thanks.
    so it will work in any position then? and it is unstalled above the water heater also.

    do i need to match the air pressure in the tank to my psi water pressure?it is about 65-70.. the...
  22. Replies
    19
    Views
    5,103

    if so ,can you answer my original question

    if so ,can you answer my original question
  23. Replies
    19
    Views
    5,103

    Im not sure if it does .It doesnt tell on the...

    Im not sure if it does .It doesnt tell on the manual.It is made by watts and is a 2 gal DET-5 or DET-12...precharged at 40psi.
  24. Replies
    19
    Views
    5,103

    expansion tank

    I had to install an expansion tank and was only able to install it with top down.It is working fine during thermal expanson psi pressure stays normal.Will it still function in a normal fashon even...
  25. Replies
    6
    Views
    1,691

    as i said im only placing a pressure reducing...

    as i said im only placing a pressure reducing valve in..nothing has broken and ive never had a pressure problem until check valve placed in line..the pressure will be 50 ,after the relief valve will...
Results 1 to 25 of 29
Page 1 of 2 1 2