Search:

Type: Posts; User: hawkins111; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    0
    Views
    35

    Laser 560 no longer made

    Early this year Toyotomi announced the Laser 560 will no longer be produced. They stated the Laser 560 was only made in the USA and dies for manufacturing had to be replaced which was too expensive....
  2. Replies
    9
    Views
    247

    All Monitor 422 units have a small damper in the...

    All Monitor 422 units have a small damper in the suction case that is held in by a screw. They all also have a second damper in the flex hose. It can be part # 6209 Air Damper S or Air Damper E for...
  3. Replies
    9
    Views
    247

    You should calibrate the fuel flow on your heater...

    You should calibrate the fuel flow on your heater before you go messing with the pump. Use a flame sensor bypass and a calibrated cup to see where you're at.

    The Air Damper should be marked 422...
  4. Replies
    3
    Views
    113

    Monitor parts are becoming harder to find...

    Monitor parts are becoming harder to find everyday. It has been since about 2008 since parts have been made for any of the Monitor line. The M2200 was one of the last models made and had a very short...
  5. Not the igniter itself but the igniter cover and...

    Not the igniter itself but the igniter cover and all other gaskets on the chamber. Not alot just a skim on either side.

    Tom
  6. The tube of glue you got with the pot goes on the...

    The tube of glue you got with the pot goes on the rope gasket only. Just a little line all the way round. Be ready when you put the glue on, as it will dry rather quickly. Monitor used burner mat...
  7. I have installed many Toyostove heaters. Very,...

    I have installed many Toyostove heaters. Very, very, very seldom is there a problem with a Toyo right out of the box. If there is, it is usually an installation problem.

    Whoever told you a Laser...
  8. Replies
    25
    Views
    2,605

    You have stated in the past you use the capsule...

    You have stated in the past you use the capsule tank. Since you have had to service the constant level valve, I think you need to look at the fuel sump that is under the capsule tank. The sump has a...
  9. Replies
    11
    Views
    2,854

    The other thing you can do to extend the time...

    The other thing you can do to extend the time between overhaul is to cut off the last bend of the flame sensor. That's the last bend that makes the sensor go straight down. That little bit removed...
  10. I have seen cracks in a M422 heat exchanger but I...

    I have seen cracks in a M422 heat exchanger but I think that was due to an over heat situtation. You can also find corrosion at the very bottom of the exchanger sometimes due to moist conditions.
  11. Replies
    11
    Views
    2,854

    In the last years of my stove business I would...

    In the last years of my stove business I would use burner mat cement to make the seam on the M422 burner ring smooth. I did have some success with that idea. The rings would last for quit a while...
  12. Replies
    25
    Views
    2,605

    In my 15 years of fixing Monitor heaters I have...

    In my 15 years of fixing Monitor heaters I have never seen an out of spec pump on a 422 or 441. That being said, the pump could be bad. I have seen a couple of pumps that had burned wiring. Since the...
  13. Replies
    25
    Views
    2,605

    You do not need to remove the tank to get the...

    You do not need to remove the tank to get the pump out, however you will need a bent screw driver to get the two screws out. I don't think there is anything wrong with the pump. Try to clean out the...
  14. Replies
    25
    Views
    2,605

    The only way to trouble shoot the pump is to use...

    The only way to trouble shoot the pump is to use your flame sensor by pass and a calibrated cup. Check the fuel flow in all three modes. Low 5.1 cc per min, high 10.3 cc per min. Check that the flow...
  15. Replies
    5
    Views
    933

    Any deformation of the burner ring is a reason to...

    Any deformation of the burner ring is a reason to replace it. The flame sensor is what is shutting the stove down. It's not broken, it's doing it's job. More than likely the sensor has soot on it....
  16. Replies
    5
    Views
    1,158

    Can you take a close up picture of the tip of...

    Can you take a close up picture of the tip of your exhaust pipe? Thanks, Tom
  17. Replies
    5
    Views
    1,158

    Check the connection from the heater to the flue...

    Check the connection from the heater to the flue pipe. This connection must be all the way together. It's a little hard to get all the way in.
  18. Replies
    6
    Views
    1,542

    Hickory Home and Garden says they still have...

    Hickory Home and Garden says they still have Monitor parts.
  19. Replies
    6
    Views
    1,542

    The 422 does have a inner piece for the nozzle...

    The 422 does have a inner piece for the nozzle port, it doesn't stick out into the center of the burner. That piece has to be installed or the brass nut will not seal with the fuel pipe.
  20. Replies
    4
    Views
    799

    The Toyo blower is a dual function unit. It sucks...

    The Toyo blower is a dual function unit. It sucks air in on the bottom fan and blows exhaust out by the top fan. The Toyo combustion system is not like the Monitor system. Monitor is what we call a...
  21. Replies
    2
    Views
    404

    The igniter gets very hot. I would not use any...

    The igniter gets very hot. I would not use any sealant on the igniter. The igniter also gets heated up by the fact the circulating fan gets dirty and reduces the air flow over the burner. All this...
  22. Replies
    4
    Views
    799

    You need to clean out the exhaust side of the...

    You need to clean out the exhaust side of the blower. It has carbon or heavy soot build up and is out of balance.

    Tom
  23. Replies
    2
    Views
    870

    Do you have the Air Damper S part # 6209...

    Do you have the Air Damper S part # 6209 installed in the air hose? If not you are getting too much air.
  24. Replies
    2
    Views
    1,225

    This is off the Toyotomi USA site EXCLUSIVE!!...

    This is off the Toyotomi USA site

    EXCLUSIVE!!

    Ultra Low Sulfur Heating Oil/Diesel (ULSHO/D) has no more than 15ppm (parts per million) of sulfur content. In 2012 New York State became the...
  25. Replies
    2
    Views
    1,225

    You have run across one of the more confusing...

    You have run across one of the more confusing issues Toyotomi has never really dealt with very well. Yes the OM 22 was certified to use #2 fuel oil, where the OM 23's use of #2 was never addressed....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4