Search:

Type: Posts; User: hawkins111; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Once the burner ring has warped it is no longer...

    Once the burner ring has warped it is no longer serviceable. The metal has changed state and will no longer stand the same amount of heat. One thing you can do to extend your service life is to use...
  2. Loose wiring harness connection for indicator...

    Loose wiring harness connection for indicator board or Reset Thermostat.
  3. The burner ring almost always needs to be...

    The burner ring almost always needs to be replaced. Even a very small warp will cause a bad flame. You will not need a rope gasket if you go through the top. Too thick a material for the burner mat...
  4. Yes you will need to open your burner and replace...

    Yes you will need to open your burner and replace the mat and ring. It is easier to remove the complete burner and heat exchanger together and access the burner from the bottom. One of the gaskets...
  5. Replies
    4
    Views
    1,595

    Greg, A sub floor platform is not necessary....

    Greg,
    A sub floor platform is not necessary. Toyotomi makes a 2" extension (20479856). You can use as many as needed. That should take up the slack very nice. Use Copper or Gray Anti Seize on the...
  6. Replies
    4
    Views
    1,595

    Woodauger, Yes the L30 and L300 exhaust...

    Woodauger, Yes the L30 and L300 exhaust components are interchangeable. If you are drilling a new hole for the L300 all the components will work fine. All you have to do is preassemble the exhaust to...
  7. Replies
    4
    Views
    994

    Lots of info on the site. The thread titled...

    Lots of info on the site. The thread titled "Monitor 441 Heater" post # 335 by Adnadeau has a great picture break down of the 441 motor and blower assy. Get good bearings if you overhaul the motor....
  8. Replies
    2
    Views
    1,172

    Were you able to fix your motor problem?

    Were you able to fix your motor problem?
  9. Replies
    2
    Views
    1,172

    If it is an original it has oil ports on both...

    If it is an original it has oil ports on both ends. These motors do not have brushes. I have had only limited success oiling the bearings. It is worth a try before you replace the motor.

    You will...
  10. Replies
    0
    Views
    474

    Toyotomi Laser 730 Power Saver feature

    The new L730 has a Power Saver feature similar to the Monitor Products units. They advertize it as a feature to save electricity when using an alternative power source. To save electricity it reduces...
  11. Replies
    0
    Views
    341

    Laser 560 no longer made

    Early this year Toyotomi announced the Laser 560 will no longer be produced. They stated the Laser 560 was only made in the USA and dies for manufacturing had to be replaced which was too expensive....
  12. Replies
    9
    Views
    1,419

    All Monitor 422 units have a small damper in the...

    All Monitor 422 units have a small damper in the suction case that is held in by a screw. They all also have a second damper in the flex hose. It can be part # 6209 Air Damper S or Air Damper E for...
  13. Replies
    9
    Views
    1,419

    You should calibrate the fuel flow on your heater...

    You should calibrate the fuel flow on your heater before you go messing with the pump. Use a flame sensor bypass and a calibrated cup to see where you're at.

    The Air Damper should be marked 422...
  14. Replies
    3
    Views
    810

    Monitor parts are becoming harder to find...

    Monitor parts are becoming harder to find everyday. It has been since about 2008 since parts have been made for any of the Monitor line. The M2200 was one of the last models made and had a very short...
  15. Replies
    10
    Views
    1,347

    Not the igniter itself but the igniter cover and...

    Not the igniter itself but the igniter cover and all other gaskets on the chamber. Not alot just a skim on either side.

    Tom
  16. Replies
    10
    Views
    1,347

    The tube of glue you got with the pot goes on the...

    The tube of glue you got with the pot goes on the rope gasket only. Just a little line all the way round. Be ready when you put the glue on, as it will dry rather quickly. Monitor used burner mat...
  17. I have installed many Toyostove heaters. Very,...

    I have installed many Toyostove heaters. Very, very, very seldom is there a problem with a Toyo right out of the box. If there is, it is usually an installation problem.

    Whoever told you a Laser...
  18. Replies
    25
    Views
    4,150

    You have stated in the past you use the capsule...

    You have stated in the past you use the capsule tank. Since you have had to service the constant level valve, I think you need to look at the fuel sump that is under the capsule tank. The sump has a...
  19. Replies
    11
    Views
    9,432

    The other thing you can do to extend the time...

    The other thing you can do to extend the time between overhaul is to cut off the last bend of the flame sensor. That's the last bend that makes the sensor go straight down. That little bit removed...
  20. I have seen cracks in a M422 heat exchanger but I...

    I have seen cracks in a M422 heat exchanger but I think that was due to an over heat situtation. You can also find corrosion at the very bottom of the exchanger sometimes due to moist conditions.
  21. Replies
    11
    Views
    9,432

    In the last years of my stove business I would...

    In the last years of my stove business I would use burner mat cement to make the seam on the M422 burner ring smooth. I did have some success with that idea. The rings would last for quit a while...
  22. Replies
    25
    Views
    4,150

    In my 15 years of fixing Monitor heaters I have...

    In my 15 years of fixing Monitor heaters I have never seen an out of spec pump on a 422 or 441. That being said, the pump could be bad. I have seen a couple of pumps that had burned wiring. Since the...
  23. Replies
    25
    Views
    4,150

    You do not need to remove the tank to get the...

    You do not need to remove the tank to get the pump out, however you will need a bent screw driver to get the two screws out. I don't think there is anything wrong with the pump. Try to clean out the...
  24. Replies
    25
    Views
    4,150

    The only way to trouble shoot the pump is to use...

    The only way to trouble shoot the pump is to use your flame sensor by pass and a calibrated cup. Check the fuel flow in all three modes. Low 5.1 cc per min, high 10.3 cc per min. Check that the flow...
  25. Replies
    5
    Views
    2,024

    Any deformation of the burner ring is a reason to...

    Any deformation of the burner ring is a reason to replace it. The flame sensor is what is shutting the stove down. It's not broken, it's doing it's job. More than likely the sensor has soot on it....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4