Search:

Type: Posts; User: hawkins111; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    13
    Views
    1,687

    In my 15 years of fixing Monitor heaters I have...

    In my 15 years of fixing Monitor heaters I have never seen an out of spec pump on a 422 or 441. That being said, the pump could be bad. I have seen a couple of pumps that had burned wiring. Since the...
  2. Replies
    13
    Views
    1,687

    You do not need to remove the tank to get the...

    You do not need to remove the tank to get the pump out, however you will need a bent screw driver to get the two screws out. I don't think there is anything wrong with the pump. Try to clean out the...
  3. Replies
    13
    Views
    1,687

    The only way to trouble shoot the pump is to use...

    The only way to trouble shoot the pump is to use your flame sensor by pass and a calibrated cup. Check the fuel flow in all three modes. Low 5.1 cc per min, high 10.3 cc per min. Check that the flow...
  4. Replies
    5
    Views
    507

    Any deformation of the burner ring is a reason to...

    Any deformation of the burner ring is a reason to replace it. The flame sensor is what is shutting the stove down. It's not broken, it's doing it's job. More than likely the sensor has soot on it....
  5. Replies
    5
    Views
    865

    Can you take a close up picture of the tip of...

    Can you take a close up picture of the tip of your exhaust pipe? Thanks, Tom
  6. Replies
    5
    Views
    865

    Check the connection from the heater to the flue...

    Check the connection from the heater to the flue pipe. This connection must be all the way together. It's a little hard to get all the way in.
  7. Replies
    6
    Views
    1,348

    Hickory Home and Garden says they still have...

    Hickory Home and Garden says they still have Monitor parts.
  8. Replies
    6
    Views
    1,348

    The 422 does have a inner piece for the nozzle...

    The 422 does have a inner piece for the nozzle port, it doesn't stick out into the center of the burner. That piece has to be installed or the brass nut will not seal with the fuel pipe.
  9. Replies
    4
    Views
    703

    The Toyo blower is a dual function unit. It sucks...

    The Toyo blower is a dual function unit. It sucks air in on the bottom fan and blows exhaust out by the top fan. The Toyo combustion system is not like the Monitor system. Monitor is what we call a...
  10. Replies
    2
    Views
    347

    The igniter gets very hot. I would not use any...

    The igniter gets very hot. I would not use any sealant on the igniter. The igniter also gets heated up by the fact the circulating fan gets dirty and reduces the air flow over the burner. All this...
  11. Replies
    4
    Views
    703

    You need to clean out the exhaust side of the...

    You need to clean out the exhaust side of the blower. It has carbon or heavy soot build up and is out of balance.

    Tom
  12. Replies
    2
    Views
    807

    Do you have the Air Damper S part # 6209...

    Do you have the Air Damper S part # 6209 installed in the air hose? If not you are getting too much air.
  13. Replies
    2
    Views
    1,129

    This is off the Toyotomi USA site EXCLUSIVE!!...

    This is off the Toyotomi USA site

    EXCLUSIVE!!

    Ultra Low Sulfur Heating Oil/Diesel (ULSHO/D) has no more than 15ppm (parts per million) of sulfur content. In 2012 New York State became the...
  14. Replies
    2
    Views
    1,129

    You have run across one of the more confusing...

    You have run across one of the more confusing issues Toyotomi has never really dealt with very well. Yes the OM 22 was certified to use #2 fuel oil, where the OM 23's use of #2 was never addressed....
  15. Replies
    2
    Views
    741

    Sorry it has taken me so long, I have been on a...

    Sorry it has taken me so long, I have been on a trip through Canada. Yes it is the controler that controls the flow. The nozzle is the same for both stoves. As an authorized Toyo Dealer switching...
  16. Thread: E01

    by hawkins111
    Replies
    9
    Views
    3,191

    The Monitor troubleshooting chart also says,...

    The Monitor troubleshooting chart also says, "Pinched wire".
  17. Thread: E01

    by hawkins111
    Replies
    9
    Views
    3,191

    What about your ground wire? You may look at the...

    What about your ground wire? You may look at the plug polarity? I'm at a lose.
  18. Replies
    3
    Views
    2,058

    Whats going on with Hickory Home and Gardens and...

    Whats going on with Hickory Home and Gardens and Monitor parts? I dont see anything on their website about Monitor.
  19. Replies
    8
    Views
    2,864

    Yes Sir Re, that will do it. Big mess. Thanks for...

    Yes Sir Re, that will do it. Big mess. Thanks for the up date.
  20. Replies
    8
    Views
    2,864

    Start your stove and look at the flame. If the...

    Start your stove and look at the flame. If the flame is strong and the stove shuts down you have something going on with the flame sensor, i.e. soot touching the rod, over heat. If the flame dies...
  21. Replies
    8
    Views
    2,864

    What was done at the full service? How long does...

    What was done at the full service? How long does the heater run after you reset it?
  22. The new electrode is too short and will not work...

    The new electrode is too short and will not work regardless of what the store guy said. You do need to provide more than AFG burner to get the correct part. The tube length makes a lot of difference...
  23. Replies
    4
    Views
    1,392

    Yes they are the older style. I never tried to...

    Yes they are the older style. I never tried to take an older style apart, so I'm not sure if the bearings will work. Sorry.
  24. Replies
    4
    Views
    1,392

    I am not sure what you have there? I have never...

    I am not sure what you have there? I have never tried to use ball bearings in an older M422 that had bronze bearings. Keep us posted as to your progress. Take some pictures when you get the motor...
  25. Replies
    5
    Views
    1,274

    You seem to have plenty of head pressure due to...

    You seem to have plenty of head pressure due to tank height. Since you have a filter and valve on your tank, it should not take much to build up a manifold. Because the filter is so close to the tank...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4