Search:

Page 1 of 5 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    0
    Views
    116

    Laser 560 no longer made

    Early this year Toyotomi announced the Laser 560 will no longer be produced. They stated the Laser 560 was only made in the USA and dies for manufacturing had to be replaced which was too expensive....
  2. I have installed many Toyostove heaters. Very,...

    I have installed many Toyostove heaters. Very, very, very seldom is there a problem with a Toyo right out of the box. If there is, it is usually an installation problem.

    Whoever told you a Laser...
  3. Replies
    25
    Views
    2,882

    You have stated in the past you use the capsule...

    You have stated in the past you use the capsule tank. Since you have had to service the constant level valve, I think you need to look at the fuel sump that is under the capsule tank. The sump has a...
  4. Replies
    11
    Views
    3,343

    The other thing you can do to extend the time...

    The other thing you can do to extend the time between overhaul is to cut off the last bend of the flame sensor. That's the last bend that makes the sensor go straight down. That little bit removed...
  5. I have seen cracks in a M422 heat exchanger but I...

    I have seen cracks in a M422 heat exchanger but I think that was due to an over heat situtation. You can also find corrosion at the very bottom of the exchanger sometimes due to moist conditions.
  6. Replies
    11
    Views
    3,343

    In the last years of my stove business I would...

    In the last years of my stove business I would use burner mat cement to make the seam on the M422 burner ring smooth. I did have some success with that idea. The rings would last for quit a while...
  7. Replies
    25
    Views
    2,882

    In my 15 years of fixing Monitor heaters I have...

    In my 15 years of fixing Monitor heaters I have never seen an out of spec pump on a 422 or 441. That being said, the pump could be bad. I have seen a couple of pumps that had burned wiring. Since the...
  8. Replies
    25
    Views
    2,882

    The only way to trouble shoot the pump is to use...

    The only way to trouble shoot the pump is to use your flame sensor by pass and a calibrated cup. Check the fuel flow in all three modes. Low 5.1 cc per min, high 10.3 cc per min. Check that the flow...
  9. Replies
    5
    Views
    1,300

    Can you take a close up picture of the tip of...

    Can you take a close up picture of the tip of your exhaust pipe? Thanks, Tom
  10. Replies
    2
    Views
    1,302

    You have run across one of the more confusing...

    You have run across one of the more confusing issues Toyotomi has never really dealt with very well. Yes the OM 22 was certified to use #2 fuel oil, where the OM 23's use of #2 was never addressed....
  11. Thread: E01

    by hawkins111
    Replies
    9
    Views
    3,499

    The Monitor troubleshooting chart also says,...

    The Monitor troubleshooting chart also says, "Pinched wire".
  12. Replies
    25
    Views
    2,882

    What about the circulating fan and cover? Are...

    What about the circulating fan and cover? Are they spotlessly clean? Then I would look at the louvers to make sure they are fully open. If you use the Economy Plus feature the stove will step down to...
  13. Replies
    28
    Views
    11,673

    The nozzle could be blocked or the pot could be...

    The nozzle could be blocked or the pot could be full of soot. What about your fueling system? Do you have good head pressure?
  14. Replies
    5
    Views
    2,694

    If the transformer was bad you would have no...

    If the transformer was bad you would have no lights or power anywhere. You can have the board repaired by Heater PC Repair. You are correct in the fact nobody in Alaska works on Monitors and nobody...
  15. Replies
    17
    Views
    5,890

    Live with it for a short while. You may have used...

    Live with it for a short while. You may have used too much glue on the mat or you have a spot on the mat that has lifted. If it does not clear up after a week you may have to do the mat again.

    Tom
  16. Replies
    2
    Views
    900

    I have used rattle can paint on louvers before,...

    I have used rattle can paint on louvers before, you just have to get it close to the original and spray the whole thing. Moisture in the house and heat from the stove over time can cause the louver...
  17. Replies
    9
    Views
    1,586

    Heater PCB Repair in North Carolina will over...

    Heater PCB Repair in North Carolina will over haul your M422 Indicator board for $90.00.
  18. Replies
    9
    Views
    1,586

    Monitor never made switches for the Switch and...

    Monitor never made switches for the Switch and Lamp. If you could get them from an electrical parts place, you would have to be very good with a solder gun to replace them.
    The Switch and Lamp part...
  19. Replies
    3
    Views
    1,135

    I'm glade you were able to get rid of the noise....

    I'm glade you were able to get rid of the noise.

    Since Monitor heater parts are becoming harder and harder to find, extending the life of your machine is important. One thing you can do to...
  20. Replies
    11
    Views
    3,012

    If the fuel sump valve is leaking and dumping...

    If the fuel sump valve is leaking and dumping fuel into the air side of the burner you will need to do a couple of things. Either fix the valve or replace it with a new sump. Fixing the valve could...
  21. Replies
    11
    Views
    3,012

    The heat exchanger being cracked is an indication...

    The heat exchanger being cracked is an indication of over heat. You should look at the burner pot. It could need a new burner mat or it could be warped. If warped it will have to be replaced. The...
  22. Replies
    28
    Views
    11,673

    The Med Solenoid has a resistance of 2300 ohm's,...

    The Med Solenoid has a resistance of 2300 ohm's, the High Solenoid is 2300 ohm's. The safety solenoid has a resistance of 1700 ohm's on both front and rear solenoids.

    The Med Sol has a voltage of...
  23. Thread: Burner Pots

    by hawkins111
    Replies
    10
    Views
    3,518

    You will need a pretty good welder to get those...

    You will need a pretty good welder to get those fuel nozzles at the right angle, but they are around. The burner ring pins are easy. I am some what surprised as I never did see a new pot that was...
  24. Finding the burner ring warped after 15 years is...

    Finding the burner ring warped after 15 years is very normal. The burner mat being lifted and broken would be normal after that time. The carbon bridge between the flame sensor would have caused the...
  25. Replies
    1
    Views
    1,295

    It would be better to have it on a lighter...

    It would be better to have it on a lighter circuit. Your compressor pulls a lot of power.

    Tom Hawkins
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4