Search:

Type: Posts; User: TechEditor; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    569

    That is what I needed to know! Thanks. Greg

    That is what I needed to know!
    Thanks.

    Greg
  2. Replies
    2
    Views
    569

    Laser 30 Igniter

    Yesterday I removed a tired burner from my 30 and replaced it with a low hr unit and I intend to rebuild the one I just took out. When I reassembled and test fired, apparently I disturbed the old...
  3. Replies
    5
    Views
    1,652

    My tank is at 18" head. I set it up that way with...

    My tank is at 18" head. I set it up that way with a rotating laser. See images for tank and valve and filter.
    28772876
    Had to get the tank quite high to get that 18". The stand is cross braced and...
  4. Replies
    5
    Views
    1,652

    Hadn't thought of a manifold. Would have to wait...

    Hadn't thought of a manifold. Would have to wait until the tank is completely empty though. (And I would prefer not to shut down the entire house for as long as it takes to re-plumb and its...
  5. Replies
    5
    Views
    1,652

    Copper Fuel Line Capacity

    With this intense cold we have been experiencing this winter, I was thinking of installing another small Laser in the Kitchen.
    Here is my setup now: From the "gravity tank", 3/8" copper to a...
  6. Replies
    4
    Views
    2,451

    What I use is a Radon fan (rated 100% duty)...

    What I use is a Radon fan (rated 100% duty) exhausting basement air and draw in fresh air from a floor register on the 1st floor and close off the basement to the outside.
  7. Replies
    4
    Views
    1,637

    It helps to have a 40 gal. Fiberglass "Temper"...

    It helps to have a 40 gal. Fiberglass "Temper" tank in-line on the feed to the water heater. it evens out seasonal water temp variations.

    TechEditor
  8. Replies
    4
    Views
    2,829

    Insurance Company that will accept a Vented Kerosene Heater w/o penalty

    Finally found an insurance company that would accept my vented kerosene heaters, Preferred Mutual. As long as the heater had a thermostat, they were happy.
  9. Replies
    4
    Views
    2,829

    When my insurance company found out I removed my...

    When my insurance company found out I removed my octopus down cellar and was running a kerosene heater (Laser 73), they removed my water damage clause for frozen pipes (they didn't freeze last winter...
  10. Given the small footprint, have you considered an...

    Given the small footprint, have you considered an instant on water heater rated for in floor heating?
  11. Replies
    6
    Views
    5,681

    Changes For Each Model L-30 versus L-300 ...

    Changes For Each Model
    L-30 versus L-300


    Single piece heat chamber and heat exchanger, just like the OM22/23.
    Exhaust stub relocated to the right. New hole will need to be done...
  12. Replies
    3
    Views
    1,303

    The plank "studs" are 1-1/2" thick

    The plank "studs" are 1-1/2" thick
  13. Replies
    3
    Views
    1,303

    1860 Timber Frame Exterior Bathroom Wall

    House was built in 1860. Re-doing the Bathroom. The exterior wall was original Horsehair Plaster, under Masonite wall board and drywall. Doing a complete gut and re-do. When I got to the lath and...
  14. Replies
    10
    Views
    3,656

    There were some days in the Alex Bay - Watertown...

    There were some days in the Alex Bay - Watertown area where the exhausts would ice up. Happened to my Laser 73 and at least a half dozen others that I know of. Combination of extreme cold and the...
  15. Running Soft Copper Fuel Line to Laser Heater

    Here is a tip that I learned the hard way on running a kerosene line with soft copper. To heat the new addition to my house I installed a Toyo Laser 30 that requires a feed from an external tank. I...
  16. Laser Intake Blockage from Snow from Roofs

    Was talking to my service man today and he told me he was running all over the county with service calls. The majority were from people shoveling off their roofs and dumping the snow on the Laser's...
  17. Replies
    0
    Views
    1,090

    Laser 73 Iced Up Intake, Smell in House

    Finally after 8 yrs of service the weather was just right that my L73's intake iced up and I got smell in the house. Called my service man and he said he was getting up to 8 calls a day because of...
  18. Replies
    3
    Views
    2,384

    It was a used unit and didn't come with one.

    It was a used unit and didn't come with one.
  19. Replies
    3
    Views
    2,384

    I added a picture.

    I added a picture.
  20. Replies
    3
    Views
    2,384

    Laser 30 EE12 High Limit Switch Activated

    The other night I had my L30 throw an EE12. The Fan screen was partially plugged. We had started hanging winter clothes above the heater and apparently all the little fuzz that was on the clothes...
  21. Replies
    17
    Views
    7,792

    Thanks to all who have helped me. I have received...

    Thanks to all who have helped me. I have received personal service notes as well as the Service Manual for the L73. Hopefully the manual for the L30 will magically appear in my in-box too. :cool:
    ...
  22. Replies
    17
    Views
    7,792

    Heard back from Rt.37, according to the...

    Heard back from Rt.37, according to the Distributor, the Service and Operators manuals have the same information in them. And they are sticking to their story even after I pointed out the...
  23. Replies
    12
    Views
    2,394

    I once ran my Kero tank dry and had to bleed each...

    I once ran my Kero tank dry and had to bleed each fitting between the tank and the heater to get fuel flow. Tank on one side of the house and the heater on the other side with "T"s for two heaters...
  24. Replies
    17
    Views
    7,792

    Stopped by Rt. 37 on Monday. They called their...

    Stopped by Rt. 37 on Monday. They called their distributor but all they could do was leave a message. Apparently no one is available this week. Rt. 37 told me they would contact me when they heard...
  25. Replies
    17
    Views
    7,792

    The Heat Exchanger sets on top of the burn...

    The Heat Exchanger sets on top of the burn chamber and the exhaust flows thru it and gives up its heat to the exchanger because of the large surface area of the exchanger. A fan blows air over and...
Results 1 to 25 of 35
Page 1 of 2 1 2