Search:

Type: Posts; User: Centurian; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Thread: Pulsator cap

    by Centurian
    Replies
    0
    Views
    1,254

    Pulsator cap

    I purchased a Samsung washer last year and two legs of the pulsator cap broke off..any idea how this can happen
    thanks in advance
  2. Replies
    4
    Views
    1,245

    More info..he valve is a lever KITZ No.58.... ...

    More info..he valve is a lever KITZ No.58.... 600WOG/150WSP 175PSI A31
  3. Replies
    4
    Views
    1,245

    This one is actually a secondary one..as the...

    This one is actually a secondary one..as the first one is in the crawl space ..this one is handy as it was installed on the first floor and in a closet so to shut off the water you don't have to go...
  4. Replies
    4
    Views
    1,245

    Ball type shut off valve

    My home water shut off valve is a lever ball type...it is very stiff to turn..after working it back and forth it gets looser but after a few days back to stiff again..any ideas ..I'm afraid to use...
  5. Thread: How come???

    by Centurian
    Replies
    6
    Views
    1,200

    How come

    could you say that rain water is distilled water,..so it does not conduct
    Since distilled water is purified and does not contain any impurities, it is unable to conduct electricity. Water ...
  6. Thread: Concrete

    by Centurian
    Replies
    1
    Views
    766

    Concrete

    I had some concrete work done in my basement...the contractors spilled some of their cleanup water down my aggregate driveway...now I have a white discoloration on the driveway...I tried power...
  7. Replies
    18
    Views
    3,927

    win 98

    don't waste your time with win 98...it was great at the time.. but has went the way of the dodo bird...microsoft will not support it and any software download you will have problems...I'm still...
  8. furnace

    I'm no expert..but it sounds to me there is inadequate combustion air which is causing the flames to seek oxygen when you put the cover on...it is called flame roll out and there is a safety switch...
  9. Replies
    4
    Views
    1,248

    hot water tank

    thanks guys...the pipe from the pressure valve is outside of the pan and is installed thru the floor into the crawl space...my plan now is to install a 45 Y in the pipe I installed to take the pan...
  10. Replies
    4
    Views
    1,248

    Hot water tank

    I purchased my home about 2 years ago and found out my hot water tank is now about 8 years old...the tank is installed above a crawl space and it sits on a tray which is about the same diameter as...
  11. Replies
    2
    Views
    1,766

    pressure switch

    Thanks Hazee..I had it the wrong way round...the pressure switch is normally open and closes on an induced draught caused by the blower motor..showing all is OK
  12. Replies
    2
    Views
    1,766

    Gas furnace safety switches

    I'm trying to get my head around the safety switches on my gas furnace Weathermaker 8000...I understand all the switches (I see 4) are all in series..any one opening will switch off the furnace)
    ...
  13. Replies
    4
    Views
    1,687

    flame roll out switch

    Problem solved...put my voltmeter across the limit switch contacts and ran the furnace ..which quit prematurely after awhile....voltmeter showed 24 volts which meant switch went open...replaced...
  14. Replies
    4
    Views
    1,687

    flame roll out switch

    Thanks Hazee an update....I changed out the programmable thermostat as it was under 3 year warranty...and all seemed Ok yesterday...but this morning when it came on it ran OK for awhile then cut out...
  15. Replies
    4
    Views
    1,687

    flame roll out switch

    I have a weathermaker 8000 gas furnace....I switched it on for the winter season a couple of days ago...before that I cleaned the flame sensor...I did notice that the sensor was a bit slack inside...
  16. Replies
    2
    Views
    912

    Rubber sealant

    HayZee....I tried that but didn't work as it's like working with glue...BUT.. I tried putting some butter on the putty knife before spreading and it worked great..any oily substance would work I...
  17. Replies
    2
    Views
    1,552

    Moisture in basement cellar

    I have a 4ft crawl space under my house ..so I installed a dehumidifier..the water discharge from it can be run to a drain..in my case I did not have a drain so the water discharge went to a...
  18. Replies
    2
    Views
    912

    Dap Butyl Flex rubber sealant

    I have been using Dap Butyl Flex rubber Sealant for small repairs to gutters etc...but I find it very difficult to work with as it sticks to the putty knife and will not spread very well...any tips...
  19. Replies
    3
    Views
    1,378

    Maytag Refrigerator

    I have a Maytag refrigerator model #MZD2665HEW...everything works OK ..but when I put my glass under the dispenser set on crushed ice..the ice splatters all over the floor...I have tried pushing the...
  20. Replies
    4
    Views
    1,601

    Bad Satellite Install

    I lived in a Strata complex once and the bylaw for installing Satellite dishes was...on the side of the home or roof....or if that was not feasible and had to be on the roof ..it could not be...
  21. Thread: Cedar

    by Centurian
    Replies
    5
    Views
    1,078

    cedar

    Thanks pushkins that is good advice...I omitted to tell you that this is no little planter..it is about 30ft long and 30in tall...so the visible screw holes are significant
  22. Thread: Cedar

    by Centurian
    Replies
    5
    Views
    1,078

    cedar

    thanks pushkins...I figured as much so that is why I asked the question...the planter is well built and the screws are on top and side..they are countersunk into the wood about in. and are...
  23. Thread: Cedar

    by Centurian
    Replies
    5
    Views
    1,078

    Cedar

    My daughter had a large wooden planter installed along her patio...it is held together with large countersunk brass screws...I was there when the painter came to finish the painting of it as it had a...
  24. Replies
    4
    Views
    2,098

    maytag refrigerator

    Again thanks Dan O...that worked
  25. Replies
    4
    Views
    2,098

    Maytag Refrigerator

    Thanks Dan O...the model number is...MZD2665HEW
Results 1 to 25 of 57
Page 1 of 3 1 2 3