Search:

Type: Posts; User: hawkins111; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    242

    Hickory Home and Garden says they still have...

    Hickory Home and Garden says they still have Monitor parts.
  2. Replies
    4
    Views
    242

    The 422 does have a inner piece for the nozzle...

    The 422 does have a inner piece for the nozzle port, it doesn't stick out into the center of the burner. That piece has to be installed or the brass nut will not seal with the fuel pipe.
  3. Replies
    4
    Views
    593

    The Toyo blower is a dual function unit. It sucks...

    The Toyo blower is a dual function unit. It sucks air in on the bottom fan and blows exhaust out by the top fan. The Toyo combustion system is not like the Monitor system. Monitor is what we call a...
  4. Replies
    2
    Views
    290

    The igniter gets very hot. I would not use any...

    The igniter gets very hot. I would not use any sealant on the igniter. The igniter also gets heated up by the fact the circulating fan gets dirty and reduces the air flow over the burner. All this...
  5. Replies
    4
    Views
    593

    You need to clean out the exhaust side of the...

    You need to clean out the exhaust side of the blower. It has carbon or heavy soot build up and is out of balance.

    Tom
  6. Replies
    2
    Views
    621

    Do you have the Air Damper S part # 6209...

    Do you have the Air Damper S part # 6209 installed in the air hose? If not you are getting too much air.
  7. Replies
    2
    Views
    1,038

    This is off the Toyotomi USA site EXCLUSIVE!!...

    This is off the Toyotomi USA site

    EXCLUSIVE!!

    Ultra Low Sulfur Heating Oil/Diesel (ULSHO/D) has no more than 15ppm (parts per million) of sulfur content. In 2012 New York State became the...
  8. Replies
    2
    Views
    1,038

    You have run across one of the more confusing...

    You have run across one of the more confusing issues Toyotomi has never really dealt with very well. Yes the OM 22 was certified to use #2 fuel oil, where the OM 23's use of #2 was never addressed....
  9. Replies
    2
    Views
    672

    Sorry it has taken me so long, I have been on a...

    Sorry it has taken me so long, I have been on a trip through Canada. Yes it is the controler that controls the flow. The nozzle is the same for both stoves. As an authorized Toyo Dealer switching...
  10. Thread: E01

    by hawkins111
    Replies
    9
    Views
    2,439

    The Monitor troubleshooting chart also says,...

    The Monitor troubleshooting chart also says, "Pinched wire".
  11. Thread: E01

    by hawkins111
    Replies
    9
    Views
    2,439

    What about your ground wire? You may look at the...

    What about your ground wire? You may look at the plug polarity? I'm at a lose.
  12. Replies
    3
    Views
    1,840

    Whats going on with Hickory Home and Gardens and...

    Whats going on with Hickory Home and Gardens and Monitor parts? I dont see anything on their website about Monitor.
  13. Replies
    8
    Views
    2,553

    Yes Sir Re, that will do it. Big mess. Thanks for...

    Yes Sir Re, that will do it. Big mess. Thanks for the up date.
  14. Replies
    8
    Views
    2,553

    Start your stove and look at the flame. If the...

    Start your stove and look at the flame. If the flame is strong and the stove shuts down you have something going on with the flame sensor, i.e. soot touching the rod, over heat. If the flame dies...
  15. Replies
    8
    Views
    2,553

    What was done at the full service? How long does...

    What was done at the full service? How long does the heater run after you reset it?
  16. The new electrode is too short and will not work...

    The new electrode is too short and will not work regardless of what the store guy said. You do need to provide more than AFG burner to get the correct part. The tube length makes a lot of difference...
  17. Replies
    4
    Views
    1,140

    Yes they are the older style. I never tried to...

    Yes they are the older style. I never tried to take an older style apart, so I'm not sure if the bearings will work. Sorry.
  18. Replies
    4
    Views
    1,140

    I am not sure what you have there? I have never...

    I am not sure what you have there? I have never tried to use ball bearings in an older M422 that had bronze bearings. Keep us posted as to your progress. Take some pictures when you get the motor...
  19. Replies
    5
    Views
    1,198

    You seem to have plenty of head pressure due to...

    You seem to have plenty of head pressure due to tank height. Since you have a filter and valve on your tank, it should not take much to build up a manifold. Because the filter is so close to the tank...
  20. Replies
    5
    Views
    1,198

    If you have good head pressure I'm sure it will...

    If you have good head pressure I'm sure it will work. If the stoves are more than 18 inches below the bottom of the tank there should be enough pressure. Those compression fittings are a no no. Use...
  21. Replies
    5
    Views
    1,198

    The science behind fluid flow and head pressure...

    The science behind fluid flow and head pressure are against you if you think a small reservoir inline with your tank will help you. The reservoir will have whatever pressure the line has. Every T,...
  22. Replies
    6
    Views
    1,256

    Fordman, Everything is the same for the new...

    Fordman, Everything is the same for the new heater, i.e. thermistor same height, Temp set at same, Economy Plus same as other heater?
  23. Replies
    6
    Views
    1,256

    What about the circulating fan and cover? Are...

    What about the circulating fan and cover? Are they spotlessly clean? Then I would look at the louvers to make sure they are fully open. If you use the Economy Plus feature the stove will step down to...
  24. Replies
    5
    Views
    1,341

    If the lift pumps are Monitor or Toyo they should...

    If the lift pumps are Monitor or Toyo they should also be just above the top of the heater. You can feed more than one heater from a lift pump as long as the run is not too far and they are on the...
  25. Replies
    5
    Views
    1,341

    You got me there. I have never seen one of those...

    You got me there. I have never seen one of those tanks. From the picture I can't see the cap, vent or outlet, however I can see that you don't have enough head pressure to get the fuel to flow...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4