Search:

Type: Posts; User: msearcher; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: E01

    by msearcher
    Replies
    9
    Views
    4,031

    Main board was the issue. Switched it and...

    Main board was the issue. Switched it and issuexwent away.
  2. Thread: E01

    by msearcher
    Replies
    9
    Views
    4,031

    Yes I saw that and have seen no signs of a...

    Yes I saw that and have seen no signs of a pinched wire.
  3. Thread: E01

    by msearcher
    Replies
    9
    Views
    4,031

    Will do, thank you

    Will do, thank you
  4. Thread: E01

    by msearcher
    Replies
    9
    Views
    4,031

    E01

    On a 441 Heater I receive E01 when I turn the heater on.

    only displays this error and beeps, does not power up.
    i have removed the flame sensor wire.

    switched main board and still received...
  5. Replies
    2
    Views
    1,843

    Thank you for the references

    Thank you for the references
  6. Replies
    2
    Views
    1,843

    441 main board question

    Anyone know what module on the board that starts the heater?

    have a board that will not allow heater to start / restart
  7. Replies
    8
    Views
    3,328

    FYI The customer said they had run for 10 years...

    FYI The customer said they had run for 10 years on #2 low sulfur on an out side tank without any service??
  8. Replies
    8
    Views
    3,328

    After servicing the second heater a second time I...

    After servicing the second heater a second time I found out the customer was burning #2 low sulfur heating fuel!!!!

    thanks everyone for your input, my FIRST question from now on... what are you...
  9. Replies
    8
    Views
    3,328

    Stove and kero tank filters are fine

    Stove and kero tank filters are fine
  10. Replies
    8
    Views
    3,328

    New factory burn pot, new burn ring, combustion...

    New factory burn pot, new burn ring, combustion and circulation bearings, damper o-ring, carb & filter cleaned.

    carbon removed from heat exchanger, air pressure set to factory spec's.

    seems to...
  11. Replies
    8
    Views
    3,328

    441 shutdown issue

    The heater shuts down with 4 bars flashing, fan continues and runs till heater is cool like normal.

    it requires a reset ( press stop & start ) to start up again, heater has just been fully...
  12. Replies
    5
    Views
    2,890

    I can tell you that the main board was bad on a...

    I can tell you that the main board was bad on a 422 heater that the igniter was good and would not work. A relay was bad.
  13. Replies
    5
    Views
    2,890

    Could be the transformer, I have both a...

    Could be the transformer, I have both a transformer and main board on eBay.
  14. Carburetor replacement

    I do have a carburetor if you need a replacement.

    send a private message to me about it if interested.

    Tom
  15. Replies
    1
    Views
    1,294

    GF500 question

    Trying to get a GF500 to run, it's LP and won't fire.

    the ignitor makes noise and can see it arc on the outside ( can't believe that is a good sign ).


    trying to run this off a LP tank - any...
  16. Sticky: I do have Jimmyj55 information, tried to post...

    I do have Jimmyj55 information, tried to post twice but it did not take?
  17. Sticky: I believe i eve I have this information saved,...

    I believe i eve I have this information saved, will look for it and post if found.
  18. Thread: 422 ignitor

    by msearcher
    Replies
    3
    Views
    3,853

    Thanks, never realized that the 422 ignitor had...

    Thanks, never realized that the 422 ignitor had longer leads, when I checked the placement on the boards I could see that the 422 needed the extra length.
  19. Thread: 422 ignitor

    by msearcher
    Replies
    3
    Views
    3,853

    422 ignitor

    I have a few m21 /m22 ignitors and see the length of the wire is shorter than the 422, any issue in extending the wires to use on a 422?
  20. Replies
    1
    Views
    1,379

    Monitor 2200 circulation Fan question

    Will a 422 fan motor fit the 2200 heater?
  21. Replies
    2
    Views
    1,571

    I did service this heater last year with new mat...

    I did service this heater last year with new mat and ring and will check them shortly. Thanks for your reply.

    Tom
  22. Replies
    2
    Views
    1,571

    Monitor 22 not putting out enough heat

    Blue ring is showing but the burn ring never glows orange. I have swapped our the pump controller and pump - no change.

    the combustion motor sevens to put out plenty of air.

    looking for...
  23. Replies
    6
    Views
    1,559

    Thank you for your response.

    Thank you for your response.
  24. Replies
    6
    Views
    1,559

    Tom i have a 22 with the large round air...

    Tom

    i have a 22 with the large round air switch like the 41 and also a 441's with both the large and later ones with the smaller square.

    tom
  25. Replies
    6
    Views
    1,559

    Thank you Tom, any way to tell a 422 from a 441...

    Thank you Tom, any way to tell a 422 from a 441 or a 22 from a 41 air pressure switch as they can look the same.

    Tom
Results 1 to 25 of 121
Page 1 of 5 1 2 3 4