Search:

Type: Posts; User: ctbale; Keyword(s):

Search: Search took 0.01 seconds.

  1. Does the fan spin free by hand?

    Does the fan spin free by hand?
  2. Replies
    5
    Views
    997

    also check the copper tube where it goes into the...

    also check the copper tube where it goes into the burner. I just had a 2200 where the tube was not tight or properly seated. It leaked between the burn pot and the exterior chamber where you could...
  3. Replies
    6
    Views
    1,429

    Thanks. I got a burn ring from Hickory Home and...

    Thanks. I got a burn ring from Hickory Home and Garden. I think thats the seller on ebay I got it from. Those burn rings are about $85 now. I got a sheet of that mcmaster cloth and cut a new...
  4. Replies
    6
    Views
    1,429

    Thanks! he says its running great but i have...

    Thanks! he says its running great but i have been wondering about that.

    Got two 422s that NOW run but the burn patterns say need to come apart. Just missed a new pot on ebay, didnt bid high enuf...
  5. Replies
    6
    Views
    1,429

    Monitor 422 Burn Pot Drip tube

    So last year I rebuilt a friends 2 heaters. A 2200 and a 422

    The question I have is I noticed that the 422's Burn Pot did not have an extension for the fuel. My 2400 and his 2200 had a tube with...
  6. Thread: E01

    by ctbale
    Replies
    9
    Views
    3,211

    Wire was good. I pulled the connector off the...

    Wire was good. I pulled the connector off the mother board. At first it cleared the E1 fault, plugged it back in and it ran for a while then came back. Pulled the flame rod and it felt like it...
  7. Thread: E01

    by ctbale
    Replies
    9
    Views
    3,211

    Working on two 422s One of mine has the E1...

    Working on two 422s

    One of mine has the E1 code also. Book says like above post says flame rod or wire is grounding. Will investigate that tomorrow. I did pull the white thermister wire, no...
  8. Thread: Laser 30 smells

    by ctbale
    Replies
    11
    Views
    4,660

    Its official!! The heat element was bent enuf...

    Its official!! The heat element was bent enuf that when it was heating and cooling there must have been movement in the heat chamber causing exhaust smell. Installed new gaskets and new heat...
  9. Thread: Laser 30 smells

    by ctbale
    Replies
    11
    Views
    4,660

    ok, I might have been premature on declaring the...

    ok, I might have been premature on declaring the heat element good. on my OP I think I said that the 6 screws were loose on my 2nd disassembly. and they were loose on the 3rd, and on the 4th the...
  10. Thread: Laser 30 smells

    by ctbale
    Replies
    11
    Views
    4,660

    It smells when on low, even when the can is not...

    It smells when on low, even when the can is not that hot. If its 55, I set it at 56 to keep it on low it stinks. It stinks when I set it to way higher then room temp also. It glows when the lights...
  11. Thread: Laser 30 smells

    by ctbale
    Replies
    11
    Views
    4,660

    pulled the mica window and gasket, small cracks...

    pulled the mica window and gasket, small cracks in the outer pane, but inner pane intact, gasket was old but solid. the plate was deformed from over tightening the screws. My guess is its original,...
  12. Thread: Laser 30 smells

    by ctbale
    Replies
    11
    Views
    4,660

    The mica window and gasket look perfect, but...

    The mica window and gasket look perfect, but guess what? I might be changing that also. After doing the burn mat cement mod, ran it this afternoon it still stinks. This is getting frustrating. Not...
  13. Thread: Laser 30 smells

    by ctbale
    Replies
    11
    Views
    4,660

    I glued the upper and lower gasket with the burn...

    I glued the upper and lower gasket with the burn mat cement to the heat chamber cylinder. They should have put more of a radius on the upper and lower edges of that "can", because like you said it...
  14. Thread: Laser 30 smells

    by ctbale
    Replies
    11
    Views
    4,660

    Thanks hawkin111 !! You gave me the motivation...

    Thanks hawkin111 !! You gave me the motivation to take my laser 30 apart AGAIN! I rebuilt it with all new gaskets, had to grind off 3 of the 6 screws on the top of the heat chamber, replaced them...
Results 1 to 14 of 14