Search:

Type: Posts; User: vipmaint70; Keyword(s):

Search: Search took 0.02 seconds.

  1. Thread: Burner Pots

    by vipmaint70
    Replies
    10
    Views
    4,359

    i actually found a guy that repaired them for me...

    i actually found a guy that repaired them for me and i have since used them all...i can order new through carswell in nc but they aren't cheap now. these parts are getting higher every year and...
  2. Replies
    6
    Views
    2,488

    Actually no but I will give them a check in the...

    Actually no but I will give them a check in the morning...thanks
  3. Replies
    2
    Views
    1,136

    I actually have used some high heat engine paint...

    I actually have used some high heat engine paint in the past to paint the grilles, advance auto parts used to sell a color that was very similar to that of the monitors, I would take my small...
  4. Replies
    6
    Views
    2,488

    Sorry I didn't explain the problem very well...

    Sorry I didn't explain the problem very well after reading it again I was confused myself...

    The original problem with the machine was that it was overfilling the tub with water and it was running...
  5. WTW5640XW0 Cabrio Washer motor getting hot

    I need some help with a washer that I am working on for a customer. He has a WTW5640XW0 Whirlpool Cabrio Washer...its the vertical modular washer type, not the one with the stater motor. His...
  6. Replies
    6
    Views
    2,488

    There was a burned spot in the board between a...

    There was a burned spot in the board between a resistor and the first pin of the p7 connector. what it was doing was not letting the fill valve cut back off during wash cycle or spin cycles it would...
  7. Replies
    6
    Views
    2,488

    Maytag Neptune MAH4000AWW doesn't start

    hey guys i have a maytag neptune washer that will start and start filling as long as you are holding the start button the led light does not light up but when you let off the button it will...
  8. Thread: Burner Pots

    by vipmaint70
    Replies
    10
    Views
    4,359

    thanks I have a guy that welds stuff for me i'll...

    thanks I have a guy that welds stuff for me i'll check and see if he has a tig
  9. Thread: Burner Pots

    by vipmaint70
    Replies
    10
    Views
    4,359

    Yeah I've been doing this for over 15 years now...

    Yeah I've been doing this for over 15 years now and this was new to me...I opened one up to put in a customers heater and was really surprised when I saw the fuel nozzle was pointing to the left...
  10. Thread: Burner Pots

    by vipmaint70
    Replies
    10
    Views
    4,359

    Burner Pots

    just wondering if any of you guys had ever purchased from monitor new burner pots with flaws...I have about 3 new 441 pots that have the fuel pipe at the wrong angle from the factory and about a...
  11. Replies
    5
    Views
    1,892

    Laser 73 bearings

    Hey guys just wondering if anyone has ever replaced the bearings on a laser 73 blower assembly...i have replaced just the motor several times and had no troubles but i have all these old motors i...
  12. Replies
    14
    Views
    8,404

    This summer on a regular service call i went out...

    This summer on a regular service call i went out to do a general cleaning on a 2400 and the same symptoms occured during startup and i found the blower motor was not running just making a humming...
  13. Replies
    9
    Views
    8,530

    I took the solenoids back off and cleaned them...

    I took the solenoids back off and cleaned them again...soaked the carb overnight in carb cleaner and replaced the rubber hose coming from the blower and this morning its running fine...so i'm...
  14. Replies
    9
    Views
    8,530

    I have cleaned the carb well, it did have some...

    I have cleaned the carb well, it did have some dirty fuel in the bottom but nothing i haven't seen before on the newer models...no signs of water being present in carb or burner itself. I cleaned the...
  15. Replies
    9
    Views
    8,530

    kerosun monitor 30 heater

    Hey guys a friend of mine dropped off an old kerosun monitor 30 heater for me to repair a few weeks ago
    and i rebuilt the burn chamber with new combustion ring, gaskets, cleaned out heat...
  16. Replies
    3
    Views
    1,892

    yeah that would be great maybe that would cut...

    yeah that would be great maybe that would cut don't on the cost of parts if another company was in the mix.
  17. Replies
    346
    Views
    227,513

    gasket material

    hazee518...i had asked you before about the gasket material from mcmaster-carr for the monitors, and i've had lots of luck using the 8799K3 silica fabric and the 9323k21 fiberglass insulation paper...
  18. Replies
    67
    Views
    13,219

    Mind if i get a copy to...

    Mind if i get a copy to please...bvipperman70@gmail.com
  19. Thread: Monitor Art

    by vipmaint70
    Replies
    8
    Views
    2,420

    burner pot ?

    Just wondering if anyone has had any luck brazing the fuel inlet back into the burner pot? I've serviced and rebuilt these heaters for 13 years now and have never attempted to fix and old pot...ive...
Results 1 to 19 of 19