Results 1 to 5 of 5

Thread: McMaster-Carr parts for Monitor 441 - burn mat and gaskets

  1. #1
    Join Date
    Jan 2013
    Posts
    9
    Thanks {vb:rawphrase post_thanks_given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts

    McMaster-Carr parts for Monitor 441 - burn mat and gaskets

    Hello,

    Regarding parts from McMaster-Carr for the Monitor 441 heater, I have ordered the items that HayZee518 posted to service my heater.

    Silica sheet goods 1/16" thick, size 40"X40" - 9362K16 - $21.50 now $33.82
    Silica Fabric - A woven fabric - .026 thick, 36" wide - order by the foot 8799K3 $9.54/ft now $10.52/ft
    Silica fabric - .090 thick, 39" wide, per foot, 8851K33 - $26.56/ft now $27.09/ft
    BOROSILICATE GLASS - Viewing window material
    1/8" thick, 2" X 1" - 8476K321 - $1.20 each – now $3.96 each

    I probably should have read his post better, as it now appears I have 3 different materials which I can use for a burn mat….and no gasket material…which is what I need most.

    Other folks mention using 9323K21 - Fiberglass Paper Ultra-High Temp Insulation roll - 10 Feet x 16” x 1/8” for their gaskets. Do I need to buy this as well, or could I cut the 9362K16 board into gaskets?

    [FYI - 9362K16 is a Heat-Shielding Millboard Insulation with a 1360 degree F maximum temperature, 39” long x 39” wide x 1/16” thick. The dimensions of this item make it expensive to ship! ($70+ in my case!!!)]

    My husband usually does the heater servicing, and he has reused the gaskets several times, so I know I will need new ones. This year he is very ill, so I’m getting a crash course in many home maintenance jobs. He rebuilt the burn chamber a year or two ago, so I'm hoping all I need to do is clean the heater and replace the gaskets.

    I'm also looking for the pdf of the 441 gasket template.

    Thanks so much!

  2. #2
    Join Date
    Aug 2008
    Location
    Bridgton, ME
    Posts
    146
    Thanks {vb:rawphrase post_thanks_given 
    0
    Thanks Thanks Received 
    28
    Thanked in
    25 Posts
    Found this on ebay
    Name:  Top Gasket.jpg
Views: 51
Size:  58.1 KB

  3. #3
    Join Date
    Aug 2008
    Location
    Bridgton, ME
    Posts
    146
    Thanks {vb:rawphrase post_thanks_given 
    0
    Thanks Thanks Received 
    28
    Thanked in
    25 Posts
    There seem to be a lot more web stores selling Monitor parts these days. It might even be cheaper to just buy the factory gasket than to buy material & cut it to size. Advance Repair Service (KeepUsWarm dot com) has the 6317 top gasket for $24 + shipping. I saw it on eBay for $19.xx & free shipping. The burn mat is also for sale at cheaper prices than it used to be.

  4. #4
    Join Date
    Dec 2011
    Posts
    324
    Thanks {vb:rawphrase post_thanks_given 
    9
    Thanks Thanks Received 
    41
    Thanked in
    40 Posts
    The 1/16" think material wouldn't be thick enough. I use 9323K21 and it works great in most cases. If I have an area that I'm in question about I simply cut two identical gaskets and double them up. If I recall correctly the only place I've done that is around the igniter. A roll of the gasket material will likely last a lifetime. Most gaskets in my 422 progressively go from one large size down to something a little smaller. Meaning the largest gasket may be something like 7.5OD (outside diameter) x 7"ID (inside diameter) another gasket be 7"OD x 6.5" ID then yet another be 6.5"OD x 6.ID. By them progressively getting smaller you can make most of the gaskets needed to do a complete gasket set out of a piece of material about 8"x8". I bought the roll I have in 2012. I've used on it and sold some pieces off of it to others who needed a piece to make gaskets out of and I've probably still got 7' or so. This is also much stronger material to work with than the original Monitor gaskets on the first use. After they've been exposed to heat for awhile they're like the Monitor gasket material in that they want to come apart when disassembled. You can buy a whole roll of this material for about the cost of 2 or 3 Monitor gaskets.
    Last edited by FordMan59; 09-25-2019 at 03:05 PM.

  5. #5
    Join Date
    Jan 2013
    Posts
    9
    Thanks {vb:rawphrase post_thanks_given 
    0
    Thanks Thanks Received 
    0
    Thanked in
    0 Posts
    Quote Originally Posted by FordMan59 View Post
    The 1/16" think material wouldn't be thick enough. I use 9323K21 and it works great in most cases. If I have an area that I'm in question about I simply cut two identical gaskets and double them up. If I recall correctly the only place I've done that is around the igniter. A roll of the gasket material will likely last a lifetime. Most gaskets in my 422 progressively go from one large size down to something a little smaller. Meaning the largest gasket may be something like 7.5OD (outside diameter) x 7"ID (inside diameter) another gasket be 7"OD x 6.5" ID then yet another be 6.5"OD x 6.ID. By them progressively getting smaller you can make most of the gaskets needed to do a complete gasket set out of a piece of material about 8"x8". I bought the roll I have in 2012. I've used on it and sold some pieces off of it to others who needed a piece to make gaskets out of and I've probably still got 7' or so. This is also much stronger material to work with than the original Monitor gaskets on the first use. After they've been exposed to heat for awhile they're like the Monitor gasket material in that they want to come apart when disassembled. You can buy a whole roll of this material for about the cost of 2 or 3 Monitor gaskets.
    Thank you FordMan! I did buy the 9323K21 and now I've got lots of gasket material, which makes me feel so much better. :-) I now have another issue, and I'll start a new thread about that...the dreaded yellow flame.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •